Tenbox 10m AM crystal

Although I've not finished off the Tenbox 10m AM transceiver yet- too cold in the workshop and too many Christmas preparations! -  I have been looking around for some low cost crystals that would be suitable for the transmitter. Ideally, I was looking for a low cost source of HC49 crystals on 29.05MHz but have not found any. Then I spotted that the German QRP-shop has 29.000MHz crystals at a reasonable 5.5 euros. I may order a couple so I can complete a pair of QRP 10m AM transceivers. I have used QRP-shop before and they give good service.

The Tenbox may not get finished until the New Year now as we have family here for the next 10 days more or less. When there are 4 grandchildren around, amateur radio takes a back seat, especially as my operating shack is used as a bedroom for the 3 and 5 year olds.

Testing the Tenbox on 10m AM today

Today I wanted check how good the Tenbox 10m AM receiver (part of the intended transceiver) was in real use as opposed to measuring it on a signal generator.

So, I set up my FT817 on 10m AM TX on the lowest power setting, which is around 150mW carrier, and fed this into a makeshift vertical tuned with the T1 ATU. Using my PC, I made a short message "G3XBM testing on 10m AM" that I played in auto-repeat.

I then went for a drive locally with the little super-regen RX in the car being fed from a vertical mag-mount antenna on the car roof. The only antenna I had was an ATX15 base loaded whip for 15m, so I pushed a few sections in to make it resonate on 29MHz.

Results were encouraging. Out in the car my 150mW AM TX beacon message could be copied out to about 2 miles away, although this was limited by QRM from W2VW (!) and VE3OWV (!) who were coming through with 59 signals on the RX on 29MHz AM. When they dropped carriers copy was fine. It's fascinating to think my 150mW AM signal was having QRM from 5000km away!

A super-regen is not really suitable for use when 10m is wide open, like it was this afternoon. Nonetheless I was able to copy stateside stations on 10m AM on a short base loaded mag-mount pretty well. For its intended purpose as a local across town natter box, I think the Tenbox is going to be fun. With 6dB more power out (my aim for it) it should be certainly possible to work G6ALB 3km away in the next village.

The next stage is now to build the TX part and test this.

Tenbox progress (10m QRP AM transceiver)

Tenbox breadboard RX -115dBm MDS

Today I breadboarded a simple, but sensitive receiver for 10m AM in the Fredbox tradition. The standard Fredbox and Sixbox circuit was simply scaled down to 29MHz with great results using the breadboard with the Marconi 2022 generator. MDS for a well modulated AM signal is better than -115dBm (around about 0.5uV) which is actually better than I was achieving on 6m and 2m. Not bad for just 2 MPF102 FETs and 1 2N3904. For the tuned circuits (RF amp output and detector) I used a couple of T37-6 (yellow) toroids tuned with 15pF trimmers. There is a 10pF coupling capactor between them.  Of course this is a super-regen with a grounded gate RF amp to isolate the detector from the antenna.

The intended use of the Tenbox is local "across town" nattering when the band is quiet. The selectivity would NOT be suitable for DX use, although I'm sure it would pick up stateside 10m AM stations OK.  I am always amazed by how well a simple super-regen RX works: they just fly for me and are always incredibly sensitive and non-critical. People who have not played with these do not know what they are missing. I highly recommend the RX in the Fredbox

Next stage is to breadboard up a simple AM modulator and TX strip. Again, I shall copy the basic Sixbox design but this time add a linear amp (a few 2N3904s in parallel as in the WISPY beacon) to get the carrier power to a useful level.

In summary, an interesting and productive hour or so after tea.

10m comes to life big time

This afternoon I took a look on 28/29MHz and the band was WIDE open. We are close to the sunspot peak - some would argue just past it - and at this time of the year conditions on the higher HF bands are at their very best. If you have never worked on 10m get on now (especially for the CQWW DX SSB contest next weekend!) and enjoy it whilst it is so very good. In 5 years from now the band will be very very different with just the occasional African and South American openings and Es propagation.

K1IED who worked many QRP AM stations on 10m today

When conditions really are this good, I recommend listening 29.0-29.1MHz for DX AM stations. Today there were some excellent AM amateur signals to be heard from the USA and Russia. K1IED was S9+ with his 250W to a big beam and he managed to work several QRP stations from Europe. In the past I have worked the USA with a few watts of AM but time prevented me having a decent try today. Andy G0FTD managed to work him with just 1W. You can see his video here.

Listening to 29.0-29.1MHz AM when the band is in good shape is like entering a time warp taking you back to how amateur radio sounded in the 1950s and early 60s. Wonderful.