VLF earth-mode mystery deepens

This afternoon I did a larger coverage test with 5W  8.977kHz earth-mode, driving in several directions locally in the car with the roof mag-mounted E-field probe RX antenna and with a PC in the car monitoring the signal. I drove for several kilometres in different directions recording where the signal could, and could not, be copied. The best reception distance with the E-field probe was 3.2km.

The map shows the results. Yellow shows where I drove and red shows where there was signal present and recorded on Spectran. I have recordings of the whole trip which I will more carefully analyse later.

5W 8.977kHz earth-mode coverage using EFP RX antenna

The interesting thing is that the signal could be copied in 4 local villages (Burwell, Reach, Exning and Swaffham Prior) but there was almost zero coverage once outside of these villages. This is NOT the case when looking with a magnetic loop RX antenna, where the signal can be copied more extensively in the rural areas at even greater distances.

It would appear that the E-field signal needs to be strong above ground to be copied with the EFP and this only happens where there are buildings i.e. in the villages. It suggests I'm detecting the signal from cables or pipes in houses.In more rural areas the signal is weaker above ground and not detected, at least not with 5W TX.

Mobile on 8.97kHz VLF

Route taken from A to F (about 4km)

Today I did a fascinating experiment on 8.977kHz VLF using my 5W earth mode transmitter and a mag-mounted E-field probe and laptop running Spectran in the car. Basically I did a "drive around" test to see where the signal could and could not be copied.

Signal strength on 4km run between 2 villages

A continuous carrier was transmitted and I continuously monitored the received signal in the car. The drive was from the middle of the next village (Swaffham Prior), out through to the main road, then back along the main road to Burwell, around part of the village and then back home to the TX location. The signal was visible in Swaffham Prior at 5-10dB S/N, then disappears and returns on approaching Burwell where it is up to 40dB/S/N in 0.18Hz bandwidth. Within Burwell it is almost solid copy. The red timing ticks are every 30 seconds.

What I am detecting (I think) is the local E-field from the VLF signal in the ground, no doubt aided by local utilities. What puzzles me is why there is NO copy in between the 2 villages when there are, I think, pipes and cables in the road.

In the coming days this test is worth repeating locally in other directions and further afield. Fascinating to think a 5W VLF signal injected into the ground can be copied on a 19 inch whip on the car roof like this.

8.97kHz earth-mode tests with mag-mounted E-field probe

Today I started some tests at 8.97kHz with my mag-mounted E-field probe (EFP) on the car roof. As usual, the transmitter was my 5W QRSS3 beacon feeding the 20m spaced earth-electrode antenna in the garden.

The logical starting point was to drive to my usual "strong" test site 1.6km from home and compare signal levels on the usual 80cm square RX loop with that on the EFP.  For reasons I have yet to understand the signal was NOT copied, even on the loop! What I did see was what looked like an FSK telemetry signal, possibly from overhead power lines close to 8.97kHz. I've never seen this before. Anyone know what it is?

8.97kHz 5W earth-mode signal at 0.4km on E-field probe

I then drove to my new QTH (due to be occupied in about 4-5 months time) which is 0.4km from the TX and sat in the car in the drive with the iPod Touch 4g running SpectrumView software connected to the EFP. The antenna was a short 19 inch whip. Signals were copied quite well (see photo showing "3" from my callsign). The bandwidth on SpectrumView cannot be narrowed enough to optimally receive QRSS3 and results would be better with the PC set to 0.34Hz bandwidth.

Tomorrow I'll have to find out why I couldn't see my earth-mode signal at the usual test site on either antenna. I'm also going to do some /M reception at 8.97kHz using the E-field probe and laptop with Spectran set to 0.34Hz or 0.17Hz bandwidth. With a continuous signal I'll be able to log the signal level as I drive around the village and nearby.

Best DX yet on 8.97kHz earth-mode: 6km QRSS3

Today I went out to my usual test sites to check the performance of my latest VLF earth-mode system. For the first time, my RX loop and preamp could be optimally tuned in the field. At 1.6km the 8.978kHz QRSS3 beacon signal was rock solid (see first image).

5W 8.978kHz QRSS3 earth-mode signal at 1.6km (STRONG)

5W 8.978kHz QRSS3 earth-mode signal at 6.0km (10dB S/N in 0.67Hz BW)

I then moved on to a number of other locations eventually arriving at a spot 6km from the 5W TX where previously I'd only ever managed copy with a constant carrier or QRSS30 (30 second dot CW). This time the signal was about 10dB over noise in 0.67Hz bandwidth on QRSS3, my best ever result at this range (second image).

In the coming week I'll be looking for a new RX test location around 7km or further from the home QTH in the hope of increasing my through-the-ground DX record.