137.5kHz WSPR reports so far today - with <20uW ERP! |
Showing posts with label g3xvl. Show all posts
Showing posts with label g3xvl. Show all posts
18 Sept 2010
137.5kHz WSPR - best DX now 61km with less than 20uW ERP
19 Sept 2009
500kHz WSPR screenshot from G3XVL
Chris, G3XVL, in Ipswich has just sent me a screenshot of my 500kHz WSPR signal this morning when I transmitted at 100% for about 30 minutes. It clearly shows the drift when I go on TX continuously. The drift is about 40-50Hz worst case. I now suspect this is drift in the FT817's reference oscillator as the box heats up and NOT drift in the transverter. I may try using the IC703 as this has a larger mass and should drift less.
The very strong signal is M0BMU and the one towards the top is G7NKS. No new reporters overnight, so it remains at 4 reporters with best DX 69kms when using less than 1mW ERP.
The very strong signal is M0BMU and the one towards the top is G7NKS. No new reporters overnight, so it remains at 4 reporters with best DX 69kms when using less than 1mW ERP.
14 Sept 2009
More QRPpp success on 500kHz
My tiny 500kHz WSPR TX station was heard 69kms away at dawn today with a report from Jim M0BMU who spotted me several times. I also had a lot more reports from G3XVL (61kms) , some 10dB stronger than his first report last night, as well as more from G6ALB (3kms).
The picture shows my 500kHz ATU on the bedroom dressing table. This is the ONLY thing between the 700mW QRP TX and the 15m of wire dangling down the back garden - no big loading coils etc. The small toroid is a 1:50 current transformer so I can measure antenna current with a multimeter. I tune up by getting the best received signal by ear adjusting tap points used, then carefully peaking the series capacitor for maximum antenna current, which barely shows anything!
Next step is to convert the transverter to full transceive which should only need the addition of a couple of relays and an RF-sensed changeover.
The picture shows my 500kHz ATU on the bedroom dressing table. This is the ONLY thing between the 700mW QRP TX and the 15m of wire dangling down the back garden - no big loading coils etc. The small toroid is a 1:50 current transformer so I can measure antenna current with a multimeter. I tune up by getting the best received signal by ear adjusting tap points used, then carefully peaking the series capacitor for maximum antenna current, which barely shows anything!
Next step is to convert the transverter to full transceive which should only need the addition of a couple of relays and an RF-sensed changeover.
13 Sept 2009
500kHz QRPpp WSPR TXing - success
Well, my unbelievably simple 500kHz station DOES get out! I've now received four WSPR beacon reports from G3XVL in Ipswich some 61kms away. I've also had lots of spots from G6ALB some 3kms away.
My rig....
Antenna: 15m of wire a few metres above ground, just 2m is vertical.
Ground: The radiator in the bedroom!
ATU: A ferrite rod with coil taps and a 500pF variable capacitor
TX: 700mW out of the PA from a 2N3904/2N3906 pair
ERP: just a few microwatts (I can barely measure the antenna current!)
Sure, a big antenna, plenty of power, a loading coil the size of a dustbin would all help get further and more often, but I am TOTALLY surprised and delighted that my ultra-simple, uWs ERP, station gets out on this most interesting band.
My rig....
Antenna: 15m of wire a few metres above ground, just 2m is vertical.
Ground: The radiator in the bedroom!
ATU: A ferrite rod with coil taps and a 500pF variable capacitor
TX: 700mW out of the PA from a 2N3904/2N3906 pair
ERP: just a few microwatts (I can barely measure the antenna current!)
Sure, a big antenna, plenty of power, a loading coil the size of a dustbin would all help get further and more often, but I am TOTALLY surprised and delighted that my ultra-simple, uWs ERP, station gets out on this most interesting band.
Subscribe to:
Posts (Atom)