Elecraft KX3 production ramp up

Elecraft KX3 units are starting to make their way into customers' hands now, although the initial product rate has been quite low. On the KX3 Yahoo Group there have been a few reports of initial huccups although this is to be expected in any new production run and, as always, Elecraft has handled these very well. According to Wayne Burdick, production is soon expected to ramp up now these initial problems are being ironed out. Wayne writes:

"Off the top of my head....  We had one unit with a dead MCU clock crystal (extremely rare). One radio wouldn't turn off because a mic wire was touching another component (we're looking at heat shrink for that). Two had problems with EEPROM due to a firmware bug I found and fixed at 1:30 AM on Monday morning. This firmware is already in beta test. 

Mostly just new-product syndrome. We really are on the verge of serious shipping increases."

 I have still to decide if/when to order one. The initial reviews on www.eham.net have been excellent.

Low cost rotator

In my search for a low cost rotator for small and lightweight VHF/UHF yagis I see that Conrad Electronics UK sells an "external TV rotator" for £52.99, plus postage from Germany with a free 2 year warranty.

3 core cable, 70 secs 360 deg rotation, 45kg load, 300Nm bending moment, 21.6Nm torque.  See eBay item 180832166179.

Does anyone have any experience of this rotator?

Rotators or big wheels

There was a time when a small rotator capable of turning a modest 2m yagi could be bought for around £40 but there appears to be little available now below £300. The low cost Yaesu rotator (G250?) appears to be unavailable now.  I was thinking about erecting small beams for 6m, 2m and 70cm and was wondering about suitable rotators, but am rather put off by the costs.

A better alternative may be a big wheel antenna with around 3dBd gain omnidirectional, or more if two are stacked. 5dBd is at least as much gain as an HB9CV without the worry of a rotator.

Elecraft KX3 leadtimes

As a potential buyer (still thinking about it), I asked the sales desk at Elecraft what sort of leadtime I could expect if I placed an order for a fully loaded , ready assembled KX3 in the next couple of weeks. This was the reply:

Roger,

Thank you for your inquiry and interest in the KX3 Transceiver.  Orders placed now will ship in 90-120 days. We are working hard to make it less than that, but right now that is my best estimate.

Thank you,
Lisa

So, 3-4 months wait currently.

Homebase-6 (50MHz halo)

Homebase-6 50MHz halo prototype indoors ready for tests

This afternoon I had a go at scaling my Homebase-10 (28MHz wire halo) down to work on 50MHz. I simply scaled the dimensions by 28.3/50.1 (the ratio of the centre frequencies) and performance was almost spot on with a low VSWR in the DX part of 6m. So far I have only tried it in the shack holding the antenna in the air by hand and keying the TX to measure SWR. Next stage of tests will be to erect it in the loft space before erecting a more permanent version within the 10m halo on the top of the mast at the back of the house at a decent height. Still, a promising start. In the end I may opt for a small 6m beam like a Moxon or HB9CV though.

UPDATE 1600z : I have now erected this horizontally in my loftspace although it is more triangular than square. Match is good so I'll see how it performs locally next.

UPDATE 2100z: I am surprised that I'm unable to copy the more distant UK 6m beacons such as GB3BUX and GB3RAL which use horizontally polarised antennas. I need to monitor for longer to see if they appear by MS or tropo.

Winter projects review

Back on Jan 4th this year I put a list of projects that were on my "to do" list on the blog. As winter is now over it is time to review progress (or rather lack of it):

Lightbeam RX. The aim is to detect the GB3CAM 481THz optical beacon at a distance of 32km from my nearest highspot.

Well, the RX has been improved considerably and is now very sensitive and is capable of NLOS reception, but I have still to make a successful reception of this beacon.

Light beam transceiver. Following on from (1), this will either be a transceive head with a transverter or an FM transceiver that I can duplicate so I can talk to others who can borrow the second unit.

This has not progressed at all. It is still my intention to do this.

Rebuilt VLF earth mode beacon transmitter. In a few weeks time I will be able to put out a stable signal on 8.97kHz  (the usual VLF test frequency) rather than 8.76kHz. My intention is to rebuild the whole beacon TX so I can run 10wpm CW, QRSS3, 30 and 60 modes as well as WSPR.

 I have recrystalled and tested the existing beacon for 8.970kHz but the full rebuild has not happened.

Improved LF loop and E-field probe antennas. I want to erect a more permanent external antenna for VLF and LF grabber work and mount these away from the house.
Improved E-field probes have been tested but I have not erected these externally.

Case up the 137kHz transverter. This has been a rat's nest on a piece of copper laminate for too long!

Still to be done.Not started.

28MHz WSPR transceiver based on a 14.060MHz crystal doubled in a DSB direct conversion transceiver circuit.
Not started and now unlikely to be done.

In my defence, I  have done a few other projects including some 160m transmitter and 160m loft antenna work and quite a bit of experimentation on the 481THz kit although few products at the end of this. I want to do one more thing very shortly and that is to erect a 50MHz (Homebase-10 style) wire halo either in the loft space or on the mast outside in time for the Es season.

In summary, I think one can say I am what my mother-in-law called a "fireside fusilier": I'm always gunner (going to) do this and gunner do that!

My old 2m AM rig

This morning, whilst clearing out some paperwork I came across this old B&W photo showing my 2m AM transceiver from the mid 1970s. It had a tunable RX covering 144-146MHz using a free-running VHF VFO (perfectly fine for AM use) and a crystal controlled transmitter; if I recall correctly, it had a few crystals that could be switched. The TX put out around 500mW of AM and was based on the PF2AM transmitter by Pye Telecom, a project I was involved with at the time. It was built in an aluminium box covered in wood effect Fablon.

The rig was also used for CW, goodness knows how, by having an external BFO held near the rig to demodulate a CW signal. Drift was a major issue on CW as you can imagine! Using this Heath Robinson arrangement I had a weekly sked with G5UM some 80km away every Monday night for several months and regularly received 559 using an HB9CV antenna in the loft.

The rig worked some useful AM DX across the UK with the best DX from home being a station in northern France one evening but it was really used as a local natter box in the Cambridge area.

When the ubiquitous Liner-2 2m SSB rig appeared I managed to buy a second hand one and this homemade AM rig was abandoned. I cannot remember what happened to it. It is nowhere to be found, so was probably taken apart for bits, which was a pity. Today I still use 2m AM from time to time and it remains a perfectly acceptable mode for local contacts with very simple kit.

KX3 reviews on eHam.net

There are now 4 reviews on www.eham.net for the new Elecraft KX3 QRP transceiver and the rating is 5 for every one so far. See http://www.eham.net/reviews/detail/10271. Although it is a lot of money it certainly looks one fantastic little radio. I am tempted!

There is a video walkthrough too by K2UM which is worth a look.

The Titanic Radio Page

Lots of interesting information and photos about the Titanic radio room at http://www.hf.ro/.

The photo shown is from the above site (I could not link it) and shows the only known photo of Titanic's radio room. It was taken by a passenger who disembarked in Ireland.

Lynton and Barnstaple Railway

On our holiday in north Devon last week we enjoyed a ride on the steam hauled Lynton and Barnstaple Railway. This is a delightful narrow gauge line that runs through a small piece of Exmoor countryside. When the line was originally build and opened in 1898 this 1ft 11.5inch gauge line ran all the way from the market town of Barnstaple to Lynton on the north coast winding its way around the hills. It included some long 1 in 50 inclines. The narrow gauge was chosen to minimise the costs and to allow tight curves on the line. It closed in 1935. Today the line is run as a trust and only over a very short length although, funds permitting, it is eventually hoped that the whole length can be reinstated as few obstructions prevent this. If you are in this part of the west country I can recommend a visit to this fascinating little line.

This is a video on YouTube showing the line as it was in 1935.