New ICOM all-band multimode

Icom have announced that they will be introducing a new multi-mode, multi-band radio called the IC7100 which includes 70MHz at 50W on some versions. This is, to my knowledge, the first time one of the big manufacturers has properly included 4m in the design. I know at least one Yaesu rig was capable of working on the band, albeit with some compromises. The new Icom rig has a separated control head with a sloping front, which is ideal for desktop operation and mobile.  It will be interesting to see the price and when it is likely to be launched. Also, whether or not they intend to do a 10W version (like the IC703) which was very popular with QRP enthusiasts.

A bit further with the WISPY RX

Although not in the best of shape today, I spotted CX1BP (11131km) and EA8FF on 10m WSPR today.  Not bad for a handful of cheap parts.

I had a bit of trouble today with the SE602 I was using for the TX part of WISPY (it may have been faulty but I was unable to get a clean DSB signal out of mine), so when I get back on the project after a week of interruptions coming up I'm going to go for the simple 2 diode single balanced mixer instead on TX. I know this works well and is less expensive.  The TX part can be simpler than the RX I believe.

Spots with WISPY RX

FR1GZ and others coming through just fine

This is the PC screen capture using WISPY as the 10m receiver for WSPR in the last hour or so. It is working just fine.

WISPY Schematic (more clearly)

For some reason when I put multiple images on a post it is not easily possible to see them clearly when clicked (at least with Firefox). So here is the schematic again. Clicking this image should bring up the full sized image clearly.

Hum fixed on the 28MHz WISPY WSPR RX

Rev B 28MHz WSPR receiver

Adding more audio decoupling around the oscillator and adding a common base FET RF preamp has totally fixed the common mode hum issues with my Polyakov mixer based DC receiver (WISPY) for 28MHz WSPR. Even running from a mains PSU I am getting good sensitivity and no hum. The board is working on the bench with no attempt at screening and appears totally fine. The oscillator buffer appears redundant, so has been removed.

Wispy Rev B (built using MeSquares)

One possible further mod is to make the input to the RF amp a series tuned circuit. This would be needed when the full transceiver version is made (back-to-back diodes would short the cap to ground on TX).  For now, I will leave the little RX running to see what I spot.

WISPY (Polyakov RX) - 1st spot

I rebuilt my 10m WSPR RX today (the rig has to be called Wispy) onto a tidier, smaller board using MeSquares and took a few steps to reduce the 50Hz common mode hum pickup, although there is still too much there and more work is needed. Someone suggested it was radiation of the 28MHz 2nd harmonic of the oscillator mixing with 50Hz in nearby PSUs being re-radiated and detected. Still unsure of the mechanism but there are lots of things to overcome this.

EA8FF on the Polyakov RX (note the 50Hz and harmonics lines locally generated)

However, the good news. The RX, even without a preamp, can detect down to an amazing -127dBm MDS, possibly lower but this is as low as my signal generator will allow and I did not try with an attenuator. My first reception of a WSPR signal was EA8FF at -18dB S/N. Remember this is a DSB RX so the noise figure is actually 3dB worse as it is picking up noise from both sidebands.

Next stage is to add a small preamp to see if this helps reduce the common mode 50Hz pick-up and increase the sensitivity another few dB.

Polyakov mixer and 50Hz hum

There is something strange about my Polyakov mixer based direct conversion receiver for 28.1246MHz WSPR at the moment.

On the bench, when connected to a 50 ohm signal generator or sitting on the bench without an antenna connected, the background noise is a quiet hiss. With an earpiece in a quiet room I can just hear a -125dBm signal, even without an RF preamp: it is a good, sensitive and simple design.

However, the moment I connect my outside halo antenna via a coax to the (unscreened) breadboard RX the 50Hz hum level is quite high, certainly some 40dB higher audio than the MDS signal. This is with the RX run from a small sealed lead acid battery. With a mains supply I might expect some hum, but what is going on? Why the high hum pickup?

My coax antenna feed passes through the loft and then outside passing plenty of mains cables, so I must be inducing some 50Hz pick-up on the coax outer which is coupling into the copper laminate breadboard ground plane. A tidy rebuild will be needed before I could put the RX into a screened box.

I do not recall having a similar problem with other DC designs I have tried (single balance diode pair, NE602, SBL1 etc.) when used in a similar lash-up breadboard.

Anyone any suggestions?

KX3 leadtimes shortening

The KX3 image on the Elecraft site

The Elecraft website now shows "New Order Lead Time: 60 days" for the KX3 10W transceiver. At one time this was around 120 days, so they are working hard to get products out more quickly now that any initial teething troubles have been addressed. www.eham.net still shows a satisfaction rating of 5 from 25 reviews, which is excellent.  A 2 month lead-time would put delivery around the end of October when DX on HF is likely to be at its best for many years.  I have to admit that I'm very tempted, but it is a lot of money.

The second 472kHz transverter (with MeSquares)

Partially built 472kHz transverter using MeSquare islands

This afternoon I started the build of my second 472kHz 10W transverter to confirm repeatability of the design. This time I'm using MeSquares from www.qrpme.com as islands to aid construction. The build is about 75% complete so I thought I'd take a photo to show the technique before the board gets too crowded. With some care the results can be almost as neat as a PCB.

MySquares and MyPads arrive

My order from www.qrpme.com arrived today by airmail from the USA. The PCB stick-down island pads look just the job and my plan is to build a second sample of my 472/500kHz transverter using these on a piece of copper laminate. There is no doubt that these pads will be a big improvement on my own rough-cut homebrew pads. I especially like the islands for SO8,  DIL8 and DIL14 ICs as fixing these with Manhattan construction has always been a real pain.