WISPY (Polyakov RX) - 1st spot

I rebuilt my 10m WSPR RX today (the rig has to be called Wispy) onto a tidier, smaller board using MeSquares and took a few steps to reduce the 50Hz common mode hum pickup, although there is still too much there and more work is needed. Someone suggested it was radiation of the 28MHz 2nd harmonic of the oscillator mixing with 50Hz in nearby PSUs being re-radiated and detected. Still unsure of the mechanism but there are lots of things to overcome this.

EA8FF on the Polyakov RX (note the 50Hz and harmonics lines locally generated)

However, the good news. The RX, even without a preamp, can detect down to an amazing -127dBm MDS, possibly lower but this is as low as my signal generator will allow and I did not try with an attenuator. My first reception of a WSPR signal was EA8FF at -18dB S/N. Remember this is a DSB RX so the noise figure is actually 3dB worse as it is picking up noise from both sidebands.

Next stage is to add a small preamp to see if this helps reduce the common mode 50Hz pick-up and increase the sensitivity another few dB.

Polyakov mixer and 50Hz hum

There is something strange about my Polyakov mixer based direct conversion receiver for 28.1246MHz WSPR at the moment.

On the bench, when connected to a 50 ohm signal generator or sitting on the bench without an antenna connected, the background noise is a quiet hiss. With an earpiece in a quiet room I can just hear a -125dBm signal, even without an RF preamp: it is a good, sensitive and simple design.

However, the moment I connect my outside halo antenna via a coax to the (unscreened) breadboard RX the 50Hz hum level is quite high, certainly some 40dB higher audio than the MDS signal. This is with the RX run from a small sealed lead acid battery. With a mains supply I might expect some hum, but what is going on? Why the high hum pickup?

My coax antenna feed passes through the loft and then outside passing plenty of mains cables, so I must be inducing some 50Hz pick-up on the coax outer which is coupling into the copper laminate breadboard ground plane. A tidy rebuild will be needed before I could put the RX into a screened box.

I do not recall having a similar problem with other DC designs I have tried (single balance diode pair, NE602, SBL1 etc.) when used in a similar lash-up breadboard.

Anyone any suggestions?

KX3 leadtimes shortening

The KX3 image on the Elecraft site

The Elecraft website now shows "New Order Lead Time: 60 days" for the KX3 10W transceiver. At one time this was around 120 days, so they are working hard to get products out more quickly now that any initial teething troubles have been addressed. www.eham.net still shows a satisfaction rating of 5 from 25 reviews, which is excellent.  A 2 month lead-time would put delivery around the end of October when DX on HF is likely to be at its best for many years.  I have to admit that I'm very tempted, but it is a lot of money.

The second 472kHz transverter (with MeSquares)

Partially built 472kHz transverter using MeSquare islands

This afternoon I started the build of my second 472kHz 10W transverter to confirm repeatability of the design. This time I'm using MeSquares from www.qrpme.com as islands to aid construction. The build is about 75% complete so I thought I'd take a photo to show the technique before the board gets too crowded. With some care the results can be almost as neat as a PCB.

MySquares and MyPads arrive

My order from www.qrpme.com arrived today by airmail from the USA. The PCB stick-down island pads look just the job and my plan is to build a second sample of my 472/500kHz transverter using these on a piece of copper laminate. There is no doubt that these pads will be a big improvement on my own rough-cut homebrew pads. I especially like the islands for SO8,  DIL8 and DIL14 ICs as fixing these with Manhattan construction has always been a real pain.

LF/MF Loop antennas on transmit

For the last few winters I've used a wire loop antenna on 136 and 500kHz transmit with moderately successful results. Well, considering the extremely low ERP it is better to say excellent results. My wire is not that thick: around 1mm PVC covered multistrand wire and the loop area around 80m square, with the lower part of the wire either very close to, or actually on, the ground.  Using the TX loop calculator at http://www.66pacific.com/calculators/small_tx_loop_calc.aspx the efficiency is around -30dB at 500kHz, so that 5W from the PA would result in around 5mW ERP radiated. My calculations and measurements, with less than ideal loop geometry, suggest the ERP is some 3dB lower at around 2-3mW. At 137kHz the loop is considerably less efficient at around -50dB.

For a small plot with nearby trees I am not sure how well this compares with a small Marconi with a short vertical section (around 6m max) and a horizontal section of around 6m. Anyone know the answer?

Another country on 472-479kHz

Lubos OK2BVG reports that he has been granted access to the new 630m MF band and is already working stations.  Gradually more countries are gaining access although I doubt UK amateurs will be allowed access to the band before January 2013.

A few years ago I was extremely excited when Lubos managed to copy my 2mW ERP 500kHz WSPR beacon at over 1000km for the first time. Since then the beacon has reached Finland at almost 1800km. 

It is good to hear that several German stations are now active in the new band with conventional CW QSOs being quite common.

RX performance comparisons (and the KX3)

http://www.sherweng.com/table.html

Sherwood carry out comprehensive tests on various amateur products. See the full list in the link above to get an idea how good the Elecraft KX3 is. Sometimes ultimate performance is unimportant but it does indicate which products are the very good ones when it matters .

Simple 28MHz Polyakov Mixer WSPR RX

As the first part of my WSPR transceiver project for 28MHz, I breadboarded a Polyakov harmonic mixer based, crystal controlled, direct conversion receiver this afternoon. It was a great success!

28MHz Polyakov mixer based WSPR RX

The circuit shows the idea implemented. A low cost GQRP club 14.060MHz crystal is pulled to 14.0623MHz in the oscillator/buffer stage. This is then injected into the back to back diode "Polyakov" harmonic mixer which switches at 2x injection frequency i.e. 28.1246MHz, the WSPR USB dial frequency. The 28MHz input from the antenna is filtered and directly applied (no RF amp) to the diode harmonic mixer with the audio output amplified and filtered in the 2 stages of audio gain. The output then goes to the PC sound card. I may improve the audio filtering and add a 600ohm line transformer between the audio output and the PC mic or line input.

Minimum discernable signal (MDS) is around -124dBm, possibly a shade better. AM rejection was tested by injecting a 100% AM modulated carrier at 28MHz. An input of -53dBm was needed before the AM signal was detected, so 70dB AM rejection, which I think is very good.

More bench work to do, then I'll try looking for 10m WSPR signals on-air with the RX, but for about an hour of work, a very fine result. Once the RX is air-test proven, the TX part will be added to make a complete WSPR transceiver.

Autumn project list

My wife often calls me a "fireside fusilier" as I am always gunner (going to) do this or gunner do that.

Well here is my current projects ideas list, some of which I hope to address in the coming weeks and months. How many will be replaced with other ideas first?

1. Finish the 472kHz transverter and write this up.
2. Simple 28MHz QRP WSPR transceiver to use with a netbook.
3. Stand alone 137kHz receiver (for use with PC).
4. Semi-permanent E-field probe antenna and on-line 137kHz/472kHz grabbers
5. More non line-of-sight light beam experiments (get better distances).
6. Semi-permanent 481THz QRSS beacon for NLOS light beam tests.
7. Alternative HF antennas - maybe re-erect my Par Electronics 40/20/10 end-fed.
8. Further earth-mode (ground conduction) experiments - tests at around 30 and 73kHz as well as more tests at VLF aiming to improve best though ground DX (currently 6km with 5W).
9. Experiment with horizontal loop antenna on TX at VLF (maximising coupling into ground).
10. Build some better LF/MF test gear such as resistive SWR bridge, 50W dummy load and a noise bridge.

I'll give you all a progress update in about 6 weeks time!