More work on the 10m DSB rig

Today I continued breadboarding the TX strip of the 10m DSB transceiver changing the single balanced mixer to a broadband design and adding/changing stages in the driver and PA. After the mixer, the driver/PA design now has 2 transistors and 1 FET PA with an output of around 1W pep. This is not enough. My aim remains at least 2W pep either from this line-up (with an IRF510 PA) or with a different PA.

Incidentally, I need a name for this rig. I used the name "Tenner" for my 10m CW transceiver, so what shall I call this one? Please give me some ideas! DSB10? Sidebander10? 10phone?

10m DSB rig progress (some)

Today I spent a little time on the transmit strip of my 10m DSB transceiver project. I started with the single balanced mixer using a T50-6 (yellow) toroid tuned to 10m, with LO injection from a signal generator and LF via a small audio preamp from an audio generator. For now I used a 1kHz tone to ensure drive levels were OK. Output is currently 20mW pep with 2 small 2N3904 linear stages following the mixer. To reach a useful RF level I therefore need another 20-23dB, easily done in two more stages. This would take me to around 2-3W pep.

HE3OM on 137.7kHz this evening

HE3OM (Switzerland) is currently active during February using an old broadcast antenna 125m long vertical. Signals in Europe are very strong despite an ERP of just a few watts. This was the QRSS3 copy this evening using Spectran and receiving on a pair of untuned earth electrodes 20m apart directly into the FT817 which is deaf at 136-137kHz, i.e. no matching and no preamps.

70.210MHz test with M0AFJ

M0AFJ's 4m CW at 75km tonight

This evening I did a test with M0AFJ in Milton Keynes about 75km west of me on 70.210MHz SSB and CW. Tim was using 80W to a 5el and I was using about 800mW into my loft dipole. M0AFJ was quite reasonable copy at times (see Spectran image of his CW - about 20dB over the noise) but Tim thinks, at best, he just copied the odd fragment of my transmission. With 20dB difference between us the result was not unexpected. I appreciated Tim trying though as I have now copied 3 stations on the band G6ALB (3km), GB3BAA (89km) and M0AFJ (75km).

4m transverter schematic

70MHz (4m) 1W pep transverter

The schematic of my QRP transverter for 4m (70MHz) is attached here and is also available on my website. Can't promise there are no errors but this is close to the real circuit as implemented. If anyone fancies having a go at this please remember this is a starting point and some optimisation of components and tuned circuit values may be needed with spreads in parts etc. As far as I am concerned this project is now complete and I have taken it as far as I want to for now.

My first 4m QSO this evening

Using my 70MHz homebrew transverter I managed my first ever 4m QSO using my own callsign this evening. I worked G6ALB on 70.2MHz SSB first and then we QSYed to 70.26MHz for an AM and an FM QSO. Reports both ways over our 3km path were fine even though we were cross-polarised. We invited others to join us, but no-one else was about. Years ago (1968) I did work ZB2VHF on 70.26MHz AM when running 4W from our university club station G3OUL.

Signs of springtime

My wife Lis with the snowdrops and aconites

Today my wife and I went for a walk to a quiet spot not far from here where we go every year about this time. At last there are signs of spring in the air with masses of white snowdrops and yellow aconite flowers. Winter is nearly done.

Look at those sunspots!!!

This morning the sunspot count is at 84 with a solar flux level 107, the first time I've seen these figures in very many years. Already PA0O is being spotted by VK2KRR on the 10m band using WSPR. If numbers like these start to become more common, as they should  during the climb up cycle 24, then 10m will be back to its old form with worldwide DX almost every day. Yippee!

Simple Sideband QRP 10m transceiver started

A long overdue project of mine is a QRP 10m simple sideband (DSB) transceiver. Having got the 4m transverter working (circuit to follow) I'm now starting work on this project in time for the summer sporadic-E season. A website to track progress on this has been started. See a Simple Sideband 10m Transceiver. With any luck this will be breadboarded by mid-March. I have included lots of links to other 10m designs from which ideas will be (or have already been) gleaned.

New record on 30m WSPR

For a change this evening I put my 5W WSPR beacon on 30m (10MHz). To my surprise I got a report from VK7DIK at a distance of 17169km. This is a new distance record for my WSPR exploits. Others have, I know, managed this sort of DX with mW powers, something that I will have to try at some point.