Loopy results on 15m

WSPR results today with 2.5W to 80cm loop in the bedroom on 15m

Well never mind the theory - my loop WORKS well. On 15m, with the loop taped to the chair in the bedroom shack, I have already been spotted on WSPR in Japan when using just 2.5W from the FT817 at  9474km.  So, my first attempt with an indoor HF magnetic loop in the bedroom has left me very impressed.

Loop antenna in the bedroom (notice the grandchildren's toys!)

Current set-up is about 80cm diameter 6mm copper pipe inductor tuned with a small 365pF air spaced variable cap. Matched with a coupling loop 1/5 the size of the main loop made with RG58 coax. With the 365pF variable it tunes from 40m-10m, but the variable cap needs padding out as tuning is extremely sharp.

I should have tried magnetic HF loops long ago.

UPDATE 1600: Just QSYed to 14MHz with the loop in the bedroom and power reduced to 500mW and still getting plenty of WSPR reports out to 2600km or so so far.

Going loopy on 10m

Prototype 10m TX loop using 6mm copper pipe

Today I've made a small TX loop for 28MHz CW/WSPR using an odd piece of 6mm copper pipe I had around the place. As I don't want to move the frequency much and the maximum power out will be 5W (usually far less) I have used a small length of twin core mains cable, trimmed to resonance, as the capacitor to resonate the antenna. The loop is matched to 50 ohms with a small coupling loop made out of RG58 coax. Bandwidth is quite sharp suggesting the loop is working as expected.  At the time of writing (early evening)  I've only copied one signal EK6RSC at 3586km earlier in the day and am still awaiting some reports on TX. The loop is mounted on a PVC pipe taped to the back of a chair in the shack.

If successful, the idea will be to put this up in the loft at the new bungalow and use it with WISPY and a small dedicated netbook PC to run 10m WSPR.

Simple, fool proof 1296MHz transverter?

Thinking about my new QTH on top of our East Anglia "hill" (aka 20m bump) I am wondering if I should consider 1296MHz operation for the first time, if only to monitor/try the band in UKAC contests with relatively local stations. Although I have listened (briefly) on 23cm years ago with a borrowed RX converter, I've never transmitted on the band with any mode.

What I am looking for is a SIMPLE transverter for the band, either a no-tune kit or a simple ready built unit. I have no test gear for this band, which is why I've not really considered the band before. The driver would be the FT817, so any suitable band could be used for the IF.

The Down East Microwave 1296MHz transverter may be a possibility. See http://croatia-microwave.blogspot.co.uk/2010/12/w1ghz-rover-transverter-for-1296-mhz.html for a report of one built.

Incidentally I remember the 23cm antenna I used back in the 1970s with the borrowed converter: it was a 4 element yagi made with 2.5mm silver plated wire. The whole antenna sat in the palm of the hand, but worked well, even indoors mounted on a piece of bamboo cane as the mast! If I remember correctly, the design was in an early edition of VHF Communications, a magazine I subscribed to back in the 1970s.

My first QSL card for a JT9 QSO

eQSL card for JT9-1 QSO

Today I see I've received an eQSL card from Manuel EA7GDC  for one of my first JT9-1 contacts on 20m last week. I much prefer eQSL cards as these don't need to be physically stored, but can be printed out if required. In the coming days I need to check my DXCC score with eQSL cards received. Although not a DX chaser really it is fun. Most of my QSOs and eQSL cards have been for 10m QSOs and next 6m QSOs.

Sporadic-E season

We are now approaching the summer sporadic-E season in the northern hemisphere with excellent 10m, 6m and 4m (plus 2m on a few occasions) propagation across Europe, the Middle East and North Africa and sometimes far beyond.

On 6m and 10m it is possible to work out to around 2000 miles quite easily with very simple omni-directional antennas and a few watts by single or multi-hop Es.

With some luck much further is possible: a few summers back I recall the thrill of working the USA on 6m with 2.5W out from the FT817 (via a coax cable with around 3dB loss) to a V2000 vertical. ERP was just over 1W. Of course CW was used for this QSO.

Keep an eye out on these bands in the next few months as you may be surprised what can be copied. Better equipped QRO stations will be working South America, deep into Africa and Japan on 6m. Even when the sunspots don't play ball, we'll still have summertime Es. Half the fun is the surprise openings to distant places that appear and sometimes disappear within a few minutes. At other times the lower VHF bands can be wide open with S9 DX signals for hours and hours.

RSGB UK VHF/UHF Activity Contests - Tuesday nights

This year I keep forgetting to have a go in the regular UKAC contests every Tuesday evening. Activity in these is usually very good and they are great fun. Last year I went out in the field to a local high spot on both 70cm and 2m and achieved some good results with just 2.5W - remember I only found out the FT817 "3 blobs" setting was not 5W in December!  Before moving in to my new East Anglian "hilltop" QTH - well it is 20m ASL :-) - I think I'll have to do some of these contests /P from the new back garden to see how the new location will be on VHF and UHF. 

Trying to fix an HP8640B sig gen ....and failing

The disconnected shaft is just to the RHS of the YIG oscillator

In my days as a young engineer (that's a long time ago) one of the "modern" pieces of test gear on the bench was an HP8640B signal generator. I used one, on and off, throughout my RF design days in the 1970s and 1980s.. On retirement I managed to borrow one on indefinite loan from a colleague who managed to buy some of the old stock items when well past their useful lifetimes. This has worked OK for several years but a few months ago the fine tune control shaft fell off inside the box. It is not broken, it just became disconnected.  Today I attempted to fix it and expected it to be easy. I could see that it was basically 2 pieces of metal connected with a small plastic part. But can I get at it?  Can I heck!

You forget how USELESS 1960s and 1970s designs were in terms of ease of manufacture and repair. To get at the part, it looks like you have to take apart about 1 zillion screws and plastic cog wheels, and all because the designer didn't put the control about 5mm  to the left, in which case none of these complicated mechanical arrangements would have been needed!  These days, where competition, manufacturing and repair costs matter, the design would not be so unnecessarily complicated. After trying to join the 2 pieces together for nearly an hour, I gave up.  In the coming days I'll return the 8640B to its owner and I expect he'll have the manual and the patience to fix it. My eyesight is also not as good as it was and that didn't help.

The tiny Elecraft XG3 signal generator (about the size of a pack of cards) would do all I need (and a lot more) and I think will be a good investment. It also weighs about 1/100th the weight of the 8640B. I am not after a signal generator with professional calibration and noise floor performance, just a simple way of checking the performance of simple receivers.

Unless absolutely necessary KISS - keep it simple stupid. This applies as much to professional gear as to amateur gear. Don't make life harder than it need be.

The KD1JV Survivor 75/80m SSB transceiver

http://www.qrpkits.com/images/survivor04a.jpg

A recent visit to Hendricks Kits shows they now sell a new (to me at least) 10W pep 80m SSB transceiver called the KD1JV Survivor inspired by the Epiphyte 80m design of a quarter of a century ago. Parts for the latter became increasingly difficult to find and this new radio uses modern parts and increases the power out. A very small, 10W pep, SSB rig for 80m is an attractive idea and is sure to be popular, especially for holiday and field use. In its basic form it is around $100 and a little more if the digital display option is added.

The specs are:

• ~10W pep @ 13.8V
• 0.2uV receiver sensitivity
• 5 pole crystal ladder filter for selectivity
• 325 or 175 kHz tuning range, selectable at build
• Coarse and Fine tuning controls
• 8 ohm - 500 mW speaker output
• SSB, CW, and, "TUNE" mode
• 50mA Rx current (with optional Digital Dial)
• Inexpensive electret microphone input
• All through hole construction
• Professional silk screened and solder masked pcb
• Full aluminum chassis w/bail, cutout for optional digital dial
• Small size, 6" x 4" x 1.5"
• Assembled weight, w/dd: 330g./11.6 oz.
• 13.8 @ 2A, min. recommended power supply

Waters and Stanton respond on the FT817ND price increase

Today I received an email from Mark Francis, the sales director at Waters & Stanton PLC regarding the price of the FT817ND. You may recall I was suspicious that the price had risen when the Yen was weakening.

Mark explained that they are working to the tightest of margins these days and the price is basically set by Yaesu. He also pointed out that compared with 25 years ago we are getting a lot more for our money reminding me that back then the same money would have bought just a 2m FT290, whereas now we get a multi-band HF/VHF/UHF, multi-mode transceiver.

So, I stand corrected and accept what Mark has said.

I'm still looking around for the best deal on a new FT817ND to compliment my 12 year old FT817 that has been used just about every day since I bought it, but may well buy from W&S if they can match the best UK price.

Windows PC bargain

After some deliberation because of adverse reviews I ordered an Asus X101ch netbook from Amazon last week. When it arrived I added a 4GB class 10 SD card running Readyboost, deleted the junk software that was not needed, added MS Essentials virus protection and got going.

Well, for under £170 new I am blown away! This little machine is great: I have already used it for WSPR and had my first JT9-1 QSO with it on 20m just a few minutes ago. Spectran seems to work too. For web browsing it is just fine. The screen resolution and clarity are good. I have not had it slow down once and it has, touch wood, not crashed yet.

In fact my view is this is an excellent little 10.1 inch Win7 netbook for the things I need. Although intended as a second PC for /P use (optical beaconing and VLF in the field) it is currently being used as my main PC and working beautifully.

The windows experience index by the way is 3.2, which I think is average.