SAQ (17.2kHz) transmission Dec 24th

The following is from the SAQ (Sweden) website:

We plan for a traditional transmission on Christmas Eve Monday 24 December. We plan to start the transmitter at 07:30 UTC and will be on air a few minutes later. A message will be sent at 08:00 UTC. The frequency is 17.2 kHz CW.

 QSL-reports are kindly received:

 QSL reports can be given via:

- E-mail to: info@alexander.n.se
- or fax to: +46-340-674195
- or via SM bureau
- or direct by mail to: Alexander - Grimeton Veteranradios Vaenner, Radiostationen, Grimeton 72, S-432 98 Grimeton, SWEDEN

Note: SAQ is a member of the Swedish Amateur Association (SSA) and "QSL via bureau" is OK.

First on-air testing of the Tenbox TX

This evening, with little sign of F2 propagation, I ventured out to test the range of the 10m Tenbox TX as it is currently. For the TX antenna I used the coax up to my 10m halo as a vertical tuned with the Elecraft T1 ATU. At the RX end, in the car, I used the FT817 with a small base loaded mag-mount.

Tenbox AM TXing with MP3 callsign message on the PC

What I should have thought about was the noise on AM from street lights! When the signal is strong in the village this is no issue at all, but traveling to the next village 3km away there were several spots where the buzz from sodium street lights just killed the little signal. Both antennas are compromised, so another 3-6dB of signal level should be possible with a proper 1/2 wave antenna at each end or with a better car antenna.

Maybe this project, although great simple fun, isn't going to quite meet my needs, whereas a DSB transceiver would?  Receiving the DSB signal as SSB and the improvement over AM will be around 9dB with better noise immunity. However a simple direct conversion RX would not be suitable to use (easily) with a DSB TX, whereas the AM Tenbox would be fully 2-way compatible with another identical AM unit.

Conclusions so far
(a) 6-10dB more may be needed to meet the design objectives with AM.
(b) It is worth repeating the very same test now using a DSB TX with the same power to compare.

The first Tenbox Schematic

The breadboarding of the Tenbox 10m AM transceiver for local cross-town night-time nattering is almost complete now, with just a receiver audio amplifier to drive a loudspeaker to be added. Power output is a conservative 250mW AM carrier (peak power around 1W).  The first schematic draft is shown here, but as always I warn that I may have forgotten to correctly label some parts and the values may change as the circuit is further developed. I hope to road test this over the weekend going out in the car with a mag-mount antenna whilst AM beaconing with the rig from home. As with WISPY, I have paralleled up 4 2N3904 transistors for the PA. This is a very inexpensive way of making a 10m PA stage! The alternative, such as a 2N3866 would be about 5-10 times more expensive.

Small Wonder Lab Kits

Dave Benson K1SWL has produced some wonderful Small Wonder Lab kits over the years including the famous RockMite transceivers, but he has decided to slow down a bit and get back to enjoying the hobby as a hobby. I think we don't realise just how much work is involved in a small ham radio company producing and supporting a range of kits. Dave's point about technical support and repairs rings bells with me: I get around 5-10 questions a week from people interested in my website projects and I am not even selling kits!

This was the notice on his website last week:

"Folks-

I took a ‘leap of faith’ in 1996, leaving the corporate world to undertake ‘Small Wonder Labs’ as a full-time venture.  Since then, it’s been a great experience.  I have to face facts, though: I’m getting older. The shortcomings in vision can be overcome with close-up glasses. More troublesome, though, are the muscular issues from spending hours a day at the computer, or with my head down, sorting parts into bowls.

Over the years, I’ve assisted countless customers with no-questions-asked replacement parts and troubleshooting advice. The issue of repairs has been problematic, though.  While no one really objects to paying $50/hour to have a $1000 rig repaired, that’s not true of a $50-100 kit. I’ve had some good people doing repair work for me, but it’s just not economically viable. Neither can I do the work in a timely manner. Therefore, and effectively immediately, I will not be accepting returns for troubleshooting/repair.

It’s not clear to me at this point if I’ll release any additional product offerings. Although I love the creative process involved in a new design, everything that follows is now just ‘work’.   Along the way, I lost the ‘hobby’ aspect of ham radio. I have not been on the air in almost 5 years. I want my hobby back!

I’ve finished our home here in the woods of New Hampshire, and it’s time for me to move on to other interests.  I’ve still got a garage/barn to build, a garden that grows larger each year, and a wealth of outdoor activities I can’t seem to find the time for. Retirement is clearly not for the faint-of-heart!

I’ll continue to sell RockMites forever, apparently.  Demand is still brisk, with more than 8000 of them out there so far. Ongoing activity for the RockMite as well as support for ‘legacy’ kits occupies me for 2-3 hours each day.  At this stage of my life, that’s ‘enough’.

73- Dave Benson, K1SWL

19 November 2012"

ARRL 10m contest (48hrs Dec 8-9th)

A reminder that the ARRL 10m contest is on next weekend (not this) over the full 48 hours Dec 8th and 9th. As conditions on 10m are pretty good right now this will be a good chance to work a fair number of US, Canadian and Mexican states and provinces, even with QRP levels in CW or SSB. I'm away on the Saturday but hope to be on for the Sunday.

Cutting big pieces of copper laminate

When I was working I had access to a guillotine to snap out large pieces of copper laminate to convenient sizes for project breadboards. Being retired I no longer have this method to hand. SO, I asked a question on the GQRP Yahoo group this evening to find out what other people did. Several suggestions but the favourite is "scoring and snapping", summarised by the post from Duncan G4DFV which I have reproduced below.

"My method of cutting large pieces of copper laminate:-

• Place a steel rule along a previously drawn line on the board where you require to cut.
• Pressing down firmly on the rule, using a stanley or other utility knife, score along the line.
• Repeat the scoring in the same cut for perhaps 10 times, then
• looking at the edges of the board, you will see each point where the
• scoring starts and finishes. 
• Carefully mark these points over on to the other side of the board and  
• place the rule exactly along a line between these points and score as before.
• After about 10 scorings, place the board on a flat surface such that the
• scored line is on a straight edge.
• Holding the board down with one hand, press down over the straight edge with the other.
• The board should break cleanly along the scored line.
• Any uneven/rough edge can be smoothed with sandpaper.

Duncan G4DFV"

Tenbox TX progress

Good progress today with the transmit side of my Tenbox 10m AM transceiver.

The series  modulator was breadboarded a few days ago, so today I built the 3rd overtone oscillator, the buffer and the modulated PA stage. Results were as expected with around 50-60mW of clean well modulated AM available at the output. With a single linear amplifier with around 10-13dB gain (easy at 29MHz) this will take me into the 500mW-1W carrier level, which is my design aim. As I did not have a suitable 29.05MHz crystal (anyone know where these can be obtained cheaply?) I used a 28.500MHz one on a dummy load. With this frequency, any range tests will have to be done at night to avoid QRM to SSB stations.

When the linear is added , maybe even before then, I'll do a local "drive around" test with the TX on "speech beaconing" mode (using an MP3 file on the PC) and with the RX attached to a mag-mount antenna on the car. This will establish the useable local coverage.  Assuming this power level is OK, I'll then complete the full design on a tidy breadboard and publish the initial schematics on my blog and website. After that, a PCB may be in order and a neat enclosure.

This project is great fun: a simple, straightforward and easily reproducible design and a project that will be useful at the end. Much more fun than working DX with 400W and a 5 el beam in a contest with a £5k commercial HF transceiver.  Honestly, I'm having a real ball with this.

10/20W versions of popular transceivers

In the Japanese home market, several of the transceivers available in the USA and Europe are available in lower power versions too. For example, the IC7000 is available as a 50W version and a 20W version. Prices aren't always lower though. For example on the www.icom.jp site, the IC7000S (20W) is available at 168000 yen, the same price as the 100W radio.

The reason these lower power radios are not available outside of Japan is clear: lack of sales volumes and lack of the necessary approvals. It is a pity that the major dealers like W&S and Martin Lynch don't offer to import these on request though if they met EMC specs as I can imagine a reasonable market with QRPers with a bit of advertising: they have enough space in RadCom and PW after all!

How to avoid expensive calls to 0870 numbers

The website http://www.saynoto0870.com/ is a useful resource in the UK if you are looking for a lower cost, or even free, way to contact companies such as Virgin Media or Dell where an expensive 0870 call make be needed.  I get infuriated when big companies keep me waiting on an expensive call saying things like, "your call is important to us" then waste the next several minutes with drivel.

Most of these alternative numbers get in "via the back door" and work on the assumption that you will be transferred internally to the correct department. It may not always work, but if you want to save a few pounds it is worth a go.

CQWW CW - guess who forgot!

Julian G4ILO has posted a piece on his excellent blog about the CQWW DX CW contest this weekend. Well, yesterday was my wife's birthday and we had family here and today I did my tax return. In the process I managed to miss this contest completely! For some reason I thought it was NEXT weekend. Never mind, there will be other occasions to work the DX.