Higher power on 137kHz

Today I did some work on increasing the output power of my 137kHz transverter used for WSPR, with mixed results. When driving the IRF540 PA with a decent square wave I can get around 24W out (was around 5-8W) from a 13.8V supply with decent efficiency. When using the drive from the mixed-down transverted signal I am having less success. The issue is driving the MOSFET gate from a really low impedance and ensuring it is as square as possible with the right mark-space ratio. Most 137kHz transmitters do this by driving at 274kHz with ICs designed to drive a pair of MOSFETs whereas I want to go in at 137kHz using discrete parts. This is a solvable challenge and I'll have this up and running in a few weeks. 25-30W would give me 6-8dB ERP improvement and more should be possible from a higher PA supply voltage. This would take my ERP up to around 0.5mW  ....heck that's high power for me!

More QRPp testing on 137.7682kHz

My QRSS30 137.7682kHz beacon is on until 0800z Tuesday morning sending XBM in QRSS30 with the full call at 10wpm periodically for full ID.  Reports (including no copy) would be much appreciated.  I'm hoping to improve on the recent best DX a few days ago - a report from G3WCB at 101km who got the signal pretty well at times despite the 140uW ERP.

CW training on the internet

If, like me, your morse code could be improved then you may like to go to http://lcwo.net/main and see the array of training material available there. It is probably the best place on the internet where you can brush up your skills.

Sunspots

At the moment we seem to be seeing quite impressive sunspot numbers, at last. See http://www.solen.info/solar/ . This bodes well for this coming autumn and winter which should see 10m well open to the USA on a regular basis by October. Such conditions offer the chance of transatlantic AM QSOs between 29-29.1MHz even with quite low power. In previous sunspot maximums it has been possible to work AM DX with just a few watts to a mag-mount on the car. AM makes a change from SSB.

Boy's Book of Crystal Sets

One of my favourite books when I first got interested in radio back in the 1960s was the Babani series book number 126 entitled The Boy's Book of Crystal Sets. The link takes you to a PDF copy of this book. I was fascinated by the shortwave version shown in the book and remember building a variety of it using parts I had. It was such fun copying distant DX stations with something so simple. Years later I managed to copy Radio Havana, All India Radio and even (directly from Australia) Radio Australia on a simple crystal set. All good simple fun showing the magic of radio. There are several websites on the internet today dealing with the design of sophisticated crystal sets capable of quite exceptional preformance.

Improved QRSS30 beacon on 137.769kHz

This afternoon I did some experimenting with some new 42mm 3C90 toroids and my 1kV WIMA polypropylene capacitors. I've managed to increase the RF output of my QRSS3/30 beacon by around 5-6dB so I've put this on beaconing over the evening and overnight period in the hope that someone will see the signal and send me some screen shots. ERP with this new beacon is around 150uW.  Previous tests with the beacon ERP at around 50uW showed that the signal could be detected in The Netherlands. Each dB gained should improve my chances of being seen ever further. The screenshot shows my signal as received 101km away by G3WCB - quite a good signal at the peak of fades.

What is my ERP currently on 137kHz WSPR?

Based on some measurements and calculations using the improved ATU (see photo) today, this is my calculation:

Measured antenna current in the TX loop = 2.13A
Area enclosed by the loop = 80 sq m
P = (I^2 x A^2)/(205 x 10^6) at 137kHz   (see p101 of "LF Today" book available from RSGB)
where P = ERP,  I = current in amps and A = loop area in sq m

P = (2.13 x 2.13 x 80 x 80)/(205 x 10^6) = 141uW

This is not a lot (but more than ever before) and this is before I start on the "ERP improvement" programme.

137/500kHz ERP improvements

Today I made a start on improving my ERP on 137kHz and 500kHz.

Firstly, I've bought a pile of Wima 1000V polypropylene capacitors from Farnell. With these I have now made a new ATU to match my TX loop (breadboard only ATU so far) which will allow me to run some 6-10dB more power into the loop without the ATU components overheating and failing. My old switched capacitor array was an old school capacitance decade box and this was marginal with tuning changing as caps heated up!

Secondly, I am going to change the MOSFET PA design to increase the 137kHz power from around 7W RF to about 30W. This should be worth around 6-8dB. I plan to do something similar on 500kHz too.

Finally, I've got some more wire to allow me to double the thickness of my TX loop. This will be done later and will be worth 2-3dB as long as I alter the 3C90 ATU (step down) matching transformer.

In all, these changes will give me up to 10-13dB more ERP and, with some luck will allow me to get more reports on QRSS and WSPR. It will take some weeks to implement these, but by late October my range should improve on both bands.

VLF NoVs to be extended

OFCOM has confirmed that the UK NoVs to operate in the 8.7-9.1kHz VLF band will be extended later this year if holders request this.  Discussions with the Met Office have confirmed no problems have been observed with operation in this band. This is good news. Currently there are, I believe, 4 VLF NoV holders in the UK: G3XIZ, G3XBM, G4WGT and G7NKS.

WSPR database issues

Some people in the UK, including me, have been unable to find wsprnet.org today. After working perfectly overnight the site just disappeared and via Virgin Media and just some other ISPs it isn't available currently. For others it works OK. This isn't the same as the recent overload issues: something has changed at their end or in the way the site connects to the internet. Hopefully all will be resolved soon or I'll have to resort to CW more often!

A useful site to check connections is http://www.downforeveryoneorjustme.com/# which allows you to check if a site has really disappeared or not. According to this, wsprnet.org is still there, so I assume it is a routing issue.

Shortly before the link was lost I was getting VK8AW well on 10m WSPR. Guess I'll have to wait now to see if my 5W WSPR signals made it to Australia this morning.....

UPDATE: 1415BST - it's back.