Amazing evening on 160m ...without an antenna

160m WSPR reports - using 5W to 20m spaced earth electrodes

What an amazing evening: tonight I let my 5W WSPR beacon run with my VLF earth electrodes (20m separation with a low wire feed) as the "antenna" i.e. no conventional antenna in the air at all. Just look at these results! 6 countries and best DX 896km to the Shetland Is. If the earth electrodes are acting as a "loop in the ground" then the Shetlands are in the wrong direction i.e. in the null of the loop.

Sunday I intend to try 137kHz with the earth electrodes as I now have some 6dB more power than the last time this was attempted.

Earth electrode "antenna" on HF

Today I had to prune the tree to which my 80m sq wire loop is attached, so the loop had to come down for a while. Instead I connected up my 20m spaced earth electrode pair "antenna" with the connecting wire about 1.5m off the ground coming back along the garden fence. This is the antenna I use on VLF earth mode tests with the best DX reception of my signal being 6km away when using 5W at 8.76kHz.

I have been amazed how well this works on 160-40m this afternoon. This is the log this evening on 160m with 5W WSPR - best DX report so far from OZ7IT at 853km. On 40m I reached over 2000km with a report from the north of Norway.

10m - still WIDE open

A small wire halo antenna, 5W from an FT817 and WSPR software and these are the loggings of my 28MHz QRP signal in just a few minutes this morning. Best DX report 16964km from VK2ALC.

481THz (light communication) progress

This afternoon I did a bit more on the optical front. I repeated my outdoor range tests using a low-cost high brightness LED as both a baseband optical transmitter and receive detector. With around 10mA TX current into the LED I was able to copy a 1kHz tone at 20m with another high brightness LED as the detector, without any additional optics other than the LED's built-in lenses at each end.

A 100mm lens properly focussed has a gain of >24dB (nearer 30dB if correctly adjusted). Assume 24dB "antenna" gain at each end of the link and we will have 48dB system gain over the simple LEDs on their own. Based on these calculations my optical transceiver should have a range of at least 5km.  If the gain of the lens is 30dB then the range could be as great as 20km. This is without using high power LEDs as the TX or using larger Fresnel lenses which would have even higher gain.

I now have the 100mm lenses I intend to use as well as 2 gun sights bought off eBay. The next step is to buy some drain pipe to house the optics. I have still to decide whether to build fully self-contained FM transceivers (simpler) or to build the optical transceive heads with separate transverters to use with the FT817.

RF skill levels

In my professional life I interviewed many graduates aspiring to become RF engineers. Very few, in recent years, had what I would call "the knowledge". By this I mean a "gut instinct" for RF that does not come from an academic course, important though this aspect is.  Rather, this "jizz" comes by living and breathing RF through building RF things yourself, however simple. A great many 2:1 graduates in communications electronics knew almost nothing about RF, had never touched a soldering iron ever and were rejected. In all honesty I believe I could sense who would make a good RF engineer within 2 minutes of the interviews starting.

Today I received a request from a Spanish amateur who professed (more or less), "I`ve a problem. I know nothing about electronics and would be unable to build the SAQ converter on your website." He then offered to pay me to build and ship the converter to him. Surely, a radio amateur in ANY country should have learnt basic RF skills as part of his training in preparation for his licence? At the most basic level the understanding may not be deep, but how can a radio amateur really not know how to put together a basic circuit?

In the UK we have a growing, and very serious, issue with poorly educated science and engineering graduates who are simply not coming out of universities with the skills needed to start work in industry. One answer was the sandwich course in which young A-level students were accepted on a company training scheme that married "on the job" skills training with educational training, usually to HND or degree level. People spotted young, with real RF "jizz" (easily judged in interviews) usually went on to become the best engineers we had.

Sunspot peak to be over 100?

The latest NOAA sunspot predictions show cycle 24 now peaking in May 2013 at a smoothed sunspot high of exactly 100. This is UP on earlier forecasts and the actual trend since this forecast was made is still upwards, I believe at a rate faster than NOAA was predicting.

So, despite the gloomy predictions of even 6 months ago, we seem to be enjoying a decent solar cycle after all with every prospect it will be better than even current forecasts suggest. Whatever, conditions on HF will continue to be good for 5 years to come, so go and enjoy them.

Today my QRP WSPR was copied in Australia a couple of times on 10m yet again. It appears that every time I fire up it gets >16000km. I just wish a few more East Coast USA stations would  come onto 6m WSPR as this is where the excitement will be for the next  few weeks if F2 MUF reaches 50.293MHz.

Busy amateur VLF weekend

G3ZJO's reception of DK7FC on 8.97kHz

Yesterday's test by DK7FC from his fixed location was a resounding success with reception all over Europe by many stations including G3ZJO, G3WCD and G3KEV, and what is believed to be the first transatlantic reception of an amateur VLF signal by a station in the Eastern USA. Results are being checked as I write.

Stefan's ERP was later re-calculated as around 800uW. It is incredible that such a tiny VLF signal can be detected so far away. If confirmed, this certainly heralds the dawn of a new and exciting phase of VLF amateur work. With another 3-6dB ERP, worldwide amateur VLF DX is now a real possibility. Of course such VLF DX reception requires incredible frequency stability, very narrow RX filters and long signal integration times; signals are far too weak to hear.

Also, Marcus DF6NM ran a 8.97kHz test today using a kite antenna. G3ZJO received a good signal in IO92ng 20dB above the noise in 424uHz bandwidth. Marcus was also well received by many other stations across Europe.

In summary, this weekend has been a BUSY one on the Dreamer's Band.

More POWER - why??

Today I see that amateurs in New Zealand are to be allowed 1kW power in future; their limit was 500W earlier I believe. I've read something about amateurs in Eire asking to be allowed 1kW in contests and I think something similar is being requested of OFCOM here.  My simple question is why?

As an example, last evening I had a totally solid QSO on CW with KT5E in Denver, Colorado on 28.060MHz 2-way QRP with 5W each end.  My antenna was a small wire halo. Like many people, I have worked well over 100 countries with QRP on CW, PSK31 and SSB and always with simple wire antennas like dipoles, never a beam.

When more power is used it just creates more splatter, and more unnecessary QRM. OK there are times when 100W rather than 5W would make QSOs much easier with fewer repeats. But do people really need to run 1kW? OK you may blast a signal through the pile-up, but do you go to bed at night with any more satisfaction than someone working DX with a few watts or even milliwatts? I very much doubt it. Power is about egos, pure and simple.

28MHz WSPR with 50mW

50mW WSPR Reports 28MHz

It really is too easy now on 28MHz! In just a few minutes, these were the reports when using just 50mW to my small halo antenna. Some reports suggest 1mW would have been enough. I need to build a bigger attenuator.

CB interference to the 28MHz band

Interference from CBers on the 28-29.7MHz band is getting worse. I guess they've been there a long time now but with good conditions their presence is more evident. Doesn't seem to cause problems with CW and WSPR operation though. The availability of rigs covering 26-30MHz capable of being easily switched from CB coverage to 10m coverage must be one of the problems and to CB operators the wide open spaces must be attractive. Use it or lose it.